EICR C1 Meaning

Share this Article:

Categories: electrical safetyLast Updated: October 27, 2026By

EICR Meaning: What Does an Electrical Installation Condition Report Mean?

EICR Meaning;

An EICR (Electrical Installation Condition Report) is an official safety document issued after an in-depth inspection and testing of a property’s fixed electrical installation. It checks the entire electrical infrastructure against national safety standards (BS 7671) and flags any potential issues, wear and tear, or non-compliant defects.

An electrician performing an EICR will identify any problems or ‘observations’ and code them according to their risk level using a code system based on red, amber and green traffic lights.

In standard UK property compliance, the meaning and core purpose of an EICR includes:

  • Verifying Electrical Safety Standards: Assessing fixed wiring, consumer units, earthing conductors, and accessories against the UK national wiring standard (BS 7671).
  • Detecting Hidden Deterioration: Pinpointing degraded cable insulation, loose terminal connections, and thermal damage before they cause electrical failure.
  • Identifying Fire and Shock Hazards: Highlighting critical missing safeguards such as lack of 30mA RCD protection or inadequate main earth bonding to gas and water supplies.
  • Fulfilling Landlord Statutory Duties: Providing legally recognized proof under the Electrical Safety Standards in the Private Rented Sector (England) Regulations 2020 that a domestic or commercial property is safe for continued occupation.

What Does an EICR C1 Mean?

EICR C1 Meaning;

An EICR (Electrical Installation Condition Report) is a document issued after an inspection of an electrical installation. It checks the property against national safety standards for electrical installations and flags any potential issues.

An electrician performing an EICR will identify any problems or ‘observations’ and code them according to their risk level using a code system based on red, amber and green traffic lights.

C1 – Dangerous (EICR C1 Meaning)

EICR C1 Meaning;

An EICR (Electrical Installation Condition Report) is a form of electrical safety inspection that will be issued once an electrician has carried out testing at your residence. It will identify any faults within your installation and grade them using BS 7671 codes C1, C2 and FI.

The C1 code is dangerous, indicating there is a potential risk of injury to anyone contacting the installation. Therefore, immediate remedial action must be taken by the owner or landlord in order to make it secure.

In most cases, if your installation has a C1 issue, this means it is unsafe for use. This could involve blocking access to the circuit or turning off the power until the issue has been addressed.

Hassan Sharif

INDUSTRY INSIGHT | HASSAN SHARIF, LANDLORD CERTIFICATE LONDON

“There is zero room for negotiation on site the moment an engineer encounters a Code 1. It isn’t an administrative advisory or a defect you schedule for next month—it is an active, live hazard with immediate potential to kill or cause a fire. If our electrician pulls off a damaged socket front and finds bare 230-volt copper exposed, or tests an ungrounded metal fitting that has gone live, standard protocol takes over instantly. We don’t wait to write up the final certificate; the circuit gets isolated on the spot and an Electrical Danger Notification is handed directly to the occupant. Cutting power to an active circuit can feel drastic to a landlord, but standing between a tenant and a lethal shock is non-negotiable.”

A C1 observation means danger is already present and immediate action is required to make the affected part of the installation safe. It should not be used for a defect that might only become dangerous in the future. The electrician should explain the danger and arrange appropriate immediate safety measures, which may include isolating the affected circuit.

Live wires exposed is a classic example of C1 Fault.

EICR C1 Meaning

Common Real-World Examples of EICR C1 Faults

A C1 fault represents an immediate threat to life and property. Common real-world examples encountered during London inspections include:

  • Exposed Live Conductors: Broken socket faceplates, cracked light switches, or severed cables where bare 230V live wires can be directly touched.
  • Conductive Metal Parts Energised with Live Voltage: Metal light fittings, radiators, or appliance casings that have become live due to an internal fault combined with missing earth bonding.
  • Active Arcing, Melting, or Scorching: Consumer unit main switches or circuit breakers that are actively smoking, melting, or emitting burning smells under load.
  • Severe Water Ingress into Live Electrics: Active plumbing leaks dripping directly into the fuse board or ceiling light fittings.
  • Reversed Polarity on Mains Supply: Live and neutral conductors reversed at the incoming mains, meaning switches only cut the neutral wire while the appliance remains permanently live at 230 volts.

What Action Must Be Taken When a C1 Is Found?

  • Immediate On-Site Isolation: The electrician will immediately make the installation safe or disconnect/isolate the affected circuit with the client’s consent.
  • Electrical Danger Notification (EDN): A formal written warning notice is issued on site detailing the urgent hazard.
  • Emergency Remedial Repairs: The circuit must remain completely isolated until a qualified electrician repairs the defect and signs off a Minor Works or Electrical Installation Certificate.

Another type of fault that would be indicated by a C2 code is the absence of mains-protected bonding or earthing. This issue is quite common in residential installations and should be rectified promptly once discovered.

Some common faults that might affect safety may include an incorrectly sized bonding conductor or lack of RCD protection device. While this could pose a risk to those using the socket outlet, others are unaffected.

C3 code does not necessarily indicate a problem and doesn’t require immediate repair; however, it may indicate that something needs improving or isn’t up to date with regulations. This could include an issue with warning lights, an older but adequate casing or another minor detail which our engineer has noticed.

EICR Classification Codes Compared (C1 vs C2 vs C3 vs FI)

EICR CodeSeverity & ClassificationOverall Report OutcomeRequired Action & Timeframe
Code 1 (C1)Danger Present (Immediate risk of injury or shock)Unsatisfactory (Fail)Immediate action required; circuit isolated on the spot.
Code 2 (C2)Potentially Dangerous (Urgent safety defect)Unsatisfactory (Fail)Remedial repairs required within 28 days by law.
Code 3 (C3)Improvement Recommended (Safety upgrade)Satisfactory (Pass)Advisory only; does not legally fail the certificate.
Further Investigation (FI)Further Investigation Needed (Hidden hazard)Unsatisfactory (Fail)Must be investigated promptly before a pass is issued.

Frequently Asked Questions About EICR C1 Codes

A C1 code stands for ‘Danger Present’. It is the most severe classification in an electrical inspection, indicating that an immediate risk of electric shock, injury, or fire exists and urgent action is needed to make the property safe.
Yes. Under professional safety regulations and duty of care, an electrician must either make the defect safe or immediately isolate (disconnect) the dangerous circuit at the consumer unit to protect occupants from harm, issuing a formal Electrical Danger Notification.
Unlike a C2 fault which allows a 28-day window for remedial repairs, a C1 fault requires immediate action. The isolated circuit cannot legally or safely be reconnected until remedial work is completed and verified by a qualified electrician.
Tenants can generally remain in the property provided the dangerous circuit is isolated and does not cut off essential services (like total heating or primary cooking facilities). If essential power is lost, emergency remedial works must be completed without delay.
Yes. Under UK private rented sector regulations, an EICR with a single C1 observation is automatically graded as Unsatisfactory. Landlords are legally non-compliant until remedial repairs are completed.
A C1 means danger is active right now (e.g., bare live wire exposed), requiring on-the-spot isolation. A C2 means potentially dangerous—the circuit is not actively shocking anyone today, but a secondary fault could create immediate danger, granting 28 days for remedial repairs.

Our Pricing

We provide fixed-fee electrical testing and remedial repair services across Greater London and the M25. If you are managing rental properties or require an urgent safety inspection following an identified defect, explore our comprehensive commercial and domestic compliance packages on our main EICR in London booking page, or review our standard residential inspection pricing below:

Property SizeElectrical Safety Certificate Price
Studio Apartment£67.99
1 – 3 Bedrooms£94.99
4 Bedrooms£104.99
5 Bedrooms£139.99

Check Out Our Other Services

Share this Article:

About the Author: Hassan Sharif

Hassan Sharif is a Business & Sales Developer at Landlord Certificate London, managing B2B relationships with estate agencies, letting agents and block managers across London and the M25. An MSc graduate in Advertising, Marketing and Media from the University of Essex, he is also a Domestic Energy Assessor, Fire Risk Assessor, and Retrofit Coordinator & Assessor, specialising in statutory property compliance and safety certification.

Leave A Comment